PDA

View Full Version : Frag Plugs Not Ideal For Attaching To LR...How To?


BigEZ77
03/26/2016, 08:49 AM
My first three corals were on live rock rubble from my LFS which were very easy to mount onto my LR. I just received an online order of frags which are all on plugs. There's not acceptable holes in the rock where I want to put some of them and I don't want to pull rock out to drill (don't want to mess with my aquascape). Wish they were just flat pieces without the plug that sticks out the bottom. Is there a fairly easy way to break off the end piece without damaging the frags so I would just have the top disc that they sit on remaining? Just the disc would be way easier to glue to my LR. Any other suggestions are also welcome.

Also, I've currently had them on a frag rack in the tank for about a week. Should I leave them there for longer before attached to LR?

Thanks,

Russell

homer1475
03/26/2016, 09:11 AM
I use a pair of wire cutters to cut the plug end off, then superglue(loctite super glue gel) the disk to my rocks

nmotz
03/26/2016, 09:12 AM
What kind of corals? I usually try to scrape SPS off the plug myself, but that's just me. Otherwise I take a hammer and a screwdriver and just chisel off the long part of the plug so that its flat before mounting. That does take some care though.

As long as the corals seem like they are behaving normally it should be ok to mount them. But remember that each position in the tank gets different light and flow so choose your locations carefully based on the type of coral.

BigEZ77
03/26/2016, 09:34 AM
Thanks both. They're zoas, palys and shrooms. Think I'll try homer's approach.

homer1475
03/26/2016, 10:36 AM
Yeah all my zoas, and palys that came on plugs I treated this way. Now after a couple months growth, I can't even see the disk anymore.

CStrickland
03/26/2016, 11:24 AM
Thanks both. They're zoas, palys and shrooms. Think I'll try homer's approach.

Is it the kind where there's a little hard thing stuck to a big plug? For those I just wiggle a flat screwdriver under the edge of the little hard thing and gently twist. It pops right off the plug. Usually just superglued on. They seem to spread better when there's not a huge cliff to grow over at the edge of the plug and you can place them much easier. Plus I've noticed some frag plugs grow algae well, like they've absorbed phos or something - it's annoying when tufts of gha or bryopsis sprout up and start competing with a new frag.

It's not a bad idea to save plugs for future use though. It's much easier to maneuver and transport tiny bits of coral when they have a handle. I bleach, scrub, dry, and hoard them :)

Hunter1998
03/26/2016, 11:44 AM
I had a local guy hook me up with this, going to be my zoa garden. He made it with Amaco (I believe that's what it's called) he also does domes for single plugs, thought I had a pic on my phone of the island piece but I don't. Here is a picture of the dome though http://uploads.tapatalk-cdn.com/20160326/93bc9daf9a0d4d480770feac7e7caaeb.jpg

Hunter1998
03/26/2016, 11:47 AM
There is a hole in the center where the plug sits in. I realize this isn't exactly what you were looking for but thought I'd share anyway. I'll post a pic of the zoa island later today if your interested

Hunter1998
03/26/2016, 11:49 AM
Here it is had it in my Facebook instant messenger. This was the pic he sent me showing me what it looked like after it was done
http://uploads.tapatalk-cdn.com/20160326/32ccdea7cf511c21b2830f2ca7416a4e.jpg

Hunter1998
03/26/2016, 11:51 AM
Pop the plug out frag it or whatever you decide to do put in new plug and repeat.

tg1966
03/26/2016, 03:02 PM
I only use small rock rubble when making frags. Never bought a frag plug. Never will. This hobby would be a much better place if frag plugs were banned from being used/sold. Who wants to glue such an unnatural eye sore to rock work in their tank? If you buy frags on those ugly things you may want to cut the coral off and glue directly to your rock work.

rags111875
03/26/2016, 03:38 PM
i ditto the earlier reply.
i use wire cutters. very little effort and it pops off.
I then use crazy glue and epoxy to attach the disc to my rock

brianr24
03/26/2016, 04:58 PM
I do exactly what Strickland said. And I agree with TG.

BigEZ77
03/26/2016, 09:13 PM
Here it is had it in my Facebook instant messenger. This was the pic he sent me showing me what it looked like after it was done
http://uploads.tapatalk-cdn.com/20160326/32ccdea7cf511c21b2830f2ca7416a4e.jpg

Very cool idea.

Hunter1998
03/26/2016, 09:29 PM
It's in the tank now but this was the only pic I had at the time I posted. I'll be adding my first designer zoas/palys on monday

gone fishin
03/27/2016, 08:39 AM
FWIW I use my dremel to cut the plug.

BigEZ77
03/27/2016, 09:14 AM
I'm gonna use the wire cutter approach. Can I do this in the tank or should I transfer the frag to a different container with tank water and do it in that?

BigEZ77
03/27/2016, 12:14 PM
Done, did it in the tank, the end pieces break off super easy with wire cutters. Used Cg Coral Glue...very easy. First time appears to be a success! Thanks for the help.

Laredotx1987
03/29/2016, 08:05 AM
Thats the way to go, ill cut the stick part of the frag plug.

Laredotx1987
03/29/2016, 08:06 AM
Nice DIY rock , easy to put your new frags