Reef Central Online Community

Reef Central Online Community (http://www.reefcentral.com/forums/index.php)
-   Chicagoland Marine Aquarium Society (CMAS) (http://www.reefcentral.com/forums/forumdisplay.php?f=180)
-   -   Conduit & Hanging Lights ??? (http://www.reefcentral.com/forums/showthread.php?t=2104016)

1boatnut 12/08/2011 07:07 AM

Conduit & Hanging Lights ???
 
So I plan on using conduit to make hangers for my light fixtures.

Currently I have 2 pieces of 10' conduit @ 1/2"

Do you think 1/2" conduit is sufficent to hang lights on that weigh somewhere between 5-7lbs?


I plan on a very simple type set-up.
Conduit secured to back of stand with a 90 degree bend over the tank. Drill hole about 1/2" in from the end of the pipe & hang the fixture

fredfish13 12/08/2011 08:10 AM

should be fine. I had one 10' piece of 1/2" and cut it in half to hang my aquaticlife 4x24 T-5 fixture. been fine for over 2 months.

jkf1983 12/08/2011 09:41 AM

I would think so. But why not just hang it from the ceiling with a stainless cable? Might be easier too.

indydog1 12/08/2011 09:46 AM

i would not make a sharp 90. a curved one would hold better.

1boatnut 12/08/2011 11:10 AM

I plan to make something like this:http://www.drsfostersmith.com/produc...LAID=525429605

Instead of using 2 hangers though,I will cross all4 to the middle and only use 1 bracket per light.

badazztealcobra 12/08/2011 01:58 PM

How tall and wide is the tank ??? I would think if possible to try to make it from one stick of conduit. Like up from the back of the tank, bend towards the front of the tank, then bend left, then bend back towards the rear of the tank again, then bend back down.

Depending how good you are with a conduit bender in your hands you could make it pretty nice, then slap a coat of black paint on it and be done.

The link you posted is coming up dead, do you have just a picture ???

1boatnut 12/08/2011 04:27 PM

1 Attachment(s)
Quote:

Originally Posted by badazztealcobra (Post 19604682)
How tall and wide is the tank ???

Its a 125 gal
72x18x21
I think from the floor to the top of the tank is around 56"

Quote:

Originally Posted by badazztealcobra (Post 19604682)
I would think if possible to try to make it from one stick of conduit.

Yes,thats what I plan on doing.

Quote:

Originally Posted by badazztealcobra (Post 19604682)
Depending how good you are with a conduit bender in your hands you could make it pretty nice, then slap a coat of black paint on it and be done.

I suck. Yes my intentions are to paint it black

Quote:

Originally Posted by badazztealcobra (Post 19604682)
The link you posted is coming up dead, do you have just a picture ???

Sorry..I attached a photo.
In this picture it shows 2 brackets for 1 light.
I plan to just use 1 bracket per light ,for a total of 3

I already cut and bent 3 pieces of conduit.
All I did was bend them at a 90 degree like in the photo.
Now the fun comes to secure them to the stand,which is about 6" from the wall:uhoh2:

cubsfan16 12/08/2011 10:20 PM

1 Attachment(s)
I went with the single piece of 3/4" and painted it black. I need to still make a minor adjustment as it is not perfectly level. Sorry for the crappy pics


http://img.tapatalk.com/aefd1b25-8d84-3255.jpg

1boatnut 12/09/2011 07:05 AM

Quote:

Originally Posted by cubsfan16 (Post 19606623)
I went with the single piece of 3/4" and painted it black. I need to still make a minor adjustment as it is not perfectly level. Sorry for the crappy pics


http://img.tapatalk.com/aefd1b25-8d84-3255.jpg

I like that.:thumbsup:
I made 3 seperate pieces,and used only 1/2"....That was what worried me.I did hang 1 light just to see,and it seemed fine.
I have not installed them yet. Maybe later today?
I kinda did just like the pic in my last post.

Well if I decide to change,conduit was 1.69 for 10'.

Heycubsfan16...What did youi use on the conduit to attach your hanging kit with?
What are they called,and where did you get them?
They almost look like whats attached to my light fixture already,but those would be nice as I only drilled holes to put my S hoook in from the hanger

cubsfan16 12/09/2011 09:42 PM

I'm not sure what the are called, they were part of the hanging kit I got from reefledslights.com there is a close up pic on their site. I bet you could find them at a homedepot or lowes

jkf1983 12/09/2011 09:56 PM

This is the cable I used you could just hang them from the ceiling as they're intended or you could use your bracket. Either way, the kit includes all mounting hardware and is very nice. Cable and hardware was even nicer than what had come with my old ati powermodule.

jkf1983 12/09/2011 09:57 PM

Link....
http://reefledlights.com/shop/hanging-kit/

1boatnut 12/09/2011 10:44 PM

Thanks guys..
The lights came with cables that had a S hook on the end so I don't need cables.
the part going into the pipe is what interests me,and would work out well.
Maybe I van take the picture to HD or Lowes and see what they have.

Thanks again

cubsfan16, I really like how you did the 1 piece application.
I'll post some pics on mine soon.
They are not painted yet though

jkf1983 12/09/2011 11:13 PM

Something like this should be perfect then... drill a hole through the conduit and have a nut on each side.
http://t0.gstatic.com/images?q=tbn:A...YnrDeowGnqb3Ay

cubsfan16 12/09/2011 11:38 PM

Looking forward to seeing it

1boatnut 12/10/2011 09:42 AM

Quote:

Originally Posted by jkf1983 (Post 19610626)
Something like this should be perfect then... drill a hole through the conduit and have a nut on each side.
http://t0.gstatic.com/images?q=tbn:A...YnrDeowGnqb3Ay

Yep,that will work

Thanks

1boatnut 12/10/2011 11:40 AM

1 Attachment(s)
Partially finished.
Still need to paint and get part for ends to hang better.

SaltyAl 12/16/2011 08:43 AM

How are you attaching the other end of the conduit? To the back of the tank? The stand? I think I want to hang my light to keep the cats off it.

Al

lexiz1 12/16/2011 09:40 AM

1/2" EMT will hold 5-7 lbs. But if you want something a little stronger use 1/2" rigid conduit. It is stronger and will not rust from the salt. Both are available at local hardware stores.

1boatnut 12/16/2011 02:58 PM

Quote:

Originally Posted by SaltyAl (Post 19634247)
How are you attaching the other end of the conduit? To the back of the tank? The stand? I think I want to hang my light to keep the cats off it.

Al

Al,I just used regular conduit straps.
1 at the top part of my stand and 1 the bottom.

Also I have mine resting on the floor behind the tank.
If I were in need to lower the lights,the only way would be to either cut the conduit,or get longer hangers.

Also I have to move my outer lights over a bit.
I guess I did not compensate for the light spread,and instead just centered all lights. Now I have shadows (darker) at both ends of the tank.

1boatnut 12/16/2011 02:59 PM

Quote:

Originally Posted by lexiz1 (Post 19634466)
1/2" EMT will hold 5-7 lbs. But if you want something a little stronger use 1/2" rigid conduit. It is stronger and will not rust from the salt. Both are available at local hardware stores.

Thanks,but too late:beer:


All times are GMT -6. The time now is 02:10 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging v3.3.0 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.