Cutting 3/8" thick glass..... score-n-snap not working.
Any tips, aside from using a wet saw, on how to cut 3/8" plate glass (not tempered obviously).
I've only cut glass up to 1/4" thick. This glass is reclaimed from an older tank that had a crack in it. I'm salvaging the glass to make a custom sump with (ie, it's free glass). I've tried twice to score/snap it and it just doesn't work. It breaks at random, sometimes following the snap, but always wandering off. Cutting tool is brand new, and I've cut lots of thinner glass. This stuff has me beat. |
Thick glass will cut exactly the same way as thin glass. The thickness is not your problem. You say this is reclaimed glass from an old tank. That leads me to believe that there are some sort of mineral deposits on the surface you are scoring and you are not getting a clean score. Try taking a razor blade to the glass where you plan on making your score and clean it until you are positive the glass is immaculate. Also, using some sort of alcohol or acetone to clean the glass helps. Make sure you are using some sort of lubrication for the score as well. HTH.
|
Quote:
As for the lube, what do you recommend? Water, WD40...?? Thanks for the help! Matt |
you need a better cutting wheel and mineral spirts like a 145 flechter wheel then once scored spray more lube on the score let it set 5mins place a broom handle under the score press down on both sides of the score will cut like butter with the right wheel
|
For the lube, you could use vegetable oil. I wouldn't use anything that could potentially contaminate your tank. Make sure to wash the glass with warm water and dish soap when you are done to remove any oily residues. It should work out pretty well for you.
|
My neighbor works with glass he claims 3/8 will some times walk or will wind up with a bevel cut ( not square ) edge if the glass is old it is harder to cut straight also he said the same thing Bananaboat said
|
Thanks for the help, all!
For the moment I'm stuck with whatever kind of glass cutting wheel you get at Lowes. I'll check around online for a 145 Fletcher. |
I have a glass cutter with a diamond instead of a wheel. It gives you a really clean score and cuts half inch with very little wander. Old glass though is always gambling.
|
If you have an old style cutter. You can take the back end of the cutter, the ball and tap the glass to make the crack run. Not too hard. This is the only way you can cut a inside circle out. The main thing is to make one single score and not pick up the cutter. Any slight off cuts can make the crack run out the wrong way.
|
I was just in same position. I practiced on a piece that was chipped pretty good. The first cut I knew the score was inconsistant and even tapping it from underneath you could see it was going to wander. Second time I really focused one smoothe ven pressure through the entire length, and it just about fell apart at the score as I was picking it up, and the cut was REALLY nice and square. It's definitely not the same animal as 1/4", but just focus on a nice smooth even pressure through the score and it's just as easy. fwiw, I lubed the wheel with WD40.
|
I cut an old glass tabletop for sump baffles. I made sure to scrape well and clean with rubbing alcohol. I placed a huge towel (to be used for rags when done) on the garage floor. Then placed the glass on top of it. I used a t-square to make my score line straight. I used a 1/4" dowel placed under the score line and firm but heavy pressure to snap a straight edge. As someone stated before sometimes the edges can bevel and I experianced that on a few of my edges. It was a learning curve to say the least...
In the end, I rented and used a wet tile saw to make the baffles with perfect edges. Just be sure to always use thick leather or cut resistant gloves and wear eye protection. HTH, Joe |
It depends on how wide of a cut you are trying to take off. If its too thin, It won't break right. Yes you can use the ball end on the underside of the score or you can take a cold chisel (ie, blunt tip) and using that under the score, tap it to make it run. Going along the entire score until you reach the end. You can see it run out the length of the score. Be careful with your arms under the score as if it lets go, it may cut your arms. We used to use arm gurads at the glass shop I worked at. This method really works for 1/2 and 3/4 plate glass. Usually wasn't needed on 3/8 but if you are trying to just take like an inch or two, It won't break right, especially for someone who isn't a glass cutter (No offense intended). Like anything, it takes practice. I have been out of it for soo long. I was suprised I still could cut well on the 3/16 I cut a couple of weeks ago. Good Luck, YMMV, Mark
|
Thanks guys, lots of great help here!
I'll be giving it another shot here soon. |
I found the following article on the Fletcher website:
https://www.fletcherviscom.com/files...tingBasics.pdf It looks like there are a few things you can do to get a better cut including getting a cutter with the proper bevel on the wheel for the thickness of glass you are cutting. I did not know there were different bevels. |
Got an suggestions or links to glass cutters (Ive only used cheapies before with limited success)
Cheers James |
Score both sides? Is that even a thing?
|
Are you sure its not tempered ?
|
Quote:
|
Score both sides is a thing. If a score is bad, you can turn the pane over and try again. Before trying to use the first score of course. The unused score will probably make it less likely to turn out well.
|
CRL toyo original supercutter- I'm a commercial glazier and this is every one I have seen in the field's cutter of choice.
http://www.crlaurence.com/crlapps/sh...86:56176&pom=0 Pretty expensive if your just going to use it a couple times. But way better grip and cutting capabilities than your average glass cutter |
Quote:
|
I cut hundreds of square feet of glass a month being a stained glass artist. A good oil lubricated cutter is a must. Also a pair of running pliers is a great asset. They a wide plier that has a curved jaw. After scoring your line, the plier is placed over the edge of the sheet and gently squeezed and you can see the crack run along the score.
|
Quote:
|
I cut this 3/8" glass on my wet tile saw with the same blade I use on porcelain tile. My advise would be aside from ppe is to go slow or you might chip tbe glass along the cut or send a running crack especially towards the end of the cut!
http://i1309.photobucket.com/albums/...ps0mrqmloa.jpg |
Quote:
|
All times are GMT -6. The time now is 03:08 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by
Advanced User Tagging v3.3.0 (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.