|
01/10/2017, 11:50 AM | #1 |
Registered Member
Join Date: Aug 2014
Location: Oceanside, CA
Posts: 457
|
White growth on my chiller piping
My chiller's copper tubing has white growth all over it. I read that the white layer is a protective coating for copper. The deal is that this layer keeps growing, and I imagine that some of the copper material is consumed during that growth. My concern is that eventually the tubing will be eaten away by this process requiring for me to replace the chiller.
Now I am thinking of coating (or saturating) that growth with some protector such as silicone spray, or such, to stop or slow down the process. The other option is to leave it alone and let time to do its thing. What do you say? |
01/10/2017, 12:33 PM | #2 |
Registered Member
Join Date: Sep 2015
Posts: 116
|
Copper coils and piping can have a coating on them to protect them from corrosion. The coating however should not be accumulating. It usually looks like a paint but is actually an epoxy. Do you have a pic? I'm going to assume its salt creep or calcium deposits. Calcium will not eat the copper but salt may be corrosive. Salt creep can be removed with water. If it's calcium vinger can be used.
Sent from my SM-N900V using Tapatalk |
01/10/2017, 02:54 PM | #3 |
RC Mod
Join Date: Mar 2002
Location: Mountain View, CA, USA
Posts: 88,616
|
I'd like to see a picture, too. Copper shouldn't be in contact with saltwater.
__________________
Jonathan Bertoni |
01/12/2017, 01:17 PM | #4 |
Registered Member
Join Date: Aug 2014
Location: Oceanside, CA
Posts: 457
|
|
01/12/2017, 01:54 PM | #5 |
Registered Member
Join Date: Sep 2014
Location: Pittsburgh, PA
Posts: 1,708
|
Looks like you have saltwater dripping back there, causing the coper to corrode. you can see the salt on the side of the chiller in the last pic, and the dried salt on the ground below it.
|
01/12/2017, 06:19 PM | #6 |
RC Mod
Join Date: Mar 2002
Location: Mountain View, CA, USA
Posts: 88,616
|
I agree that saltwater seems to be getting onto the chiller. That's going to cause a lot of corrosion. It might be possible that this is the effect of condensation combined with saltwater in the air, as well. As another possibility, there might be a slow leak or two. I'd get someone who understands this type of piping to look at the setup if you can't find a saltwater source that is leaking onto the setup.
__________________
Jonathan Bertoni |
01/12/2017, 09:09 PM | #7 |
Registered Member
Join Date: Jan 2016
Posts: 52
|
You might wanna find a safe way to remove that build up with a baking soda/water solution.
Sent from my iPad using Tapatalk |
12/14/2017, 12:32 PM | #8 |
Registered Member
Join Date: Aug 2014
Location: Oceanside, CA
Posts: 457
|
Almost a year later, as a follow up, I finally removed the chiller, rinsed the piping with vinegar, then water. Once dry, I painted the copper pipes with lacquer.
Now it looks like new. |
12/20/2017, 05:52 PM | #9 |
Registered Bumm
Join Date: Apr 2009
Location: South Florida
Posts: 176
|
Those pipes are holding refrigerant not saltwater . Like everyone has said saltwater is dripping on it and if it corrodes too much you will lose your 134A charge and then chiller quits! Usually the device the saltwater is going through is made from titanium .
|
12/20/2017, 07:46 PM | #10 |
RC Mod
Join Date: Mar 2002
Location: Mountain View, CA, USA
Posts: 88,616
|
So there wasn't much corrosion of the pipes yet? That's good to know.
__________________
Jonathan Bertoni |
|
|