|
05/07/2010, 08:31 AM | #1 |
Registered Member
Join Date: Apr 2005
Location: Lexington, KY
Posts: 2
|
HQI Lighting Burning up corals?
I have a 180 Gallon aquarium, which has a 60-Gallon sump containing cured live rock, a 6" Protein Skimmer, and a 40-gallon refugium. All of this has been up and running for about two years. The lighting system has three HQI metal halide bulbs and two 96watt compact actinic fluorescents.
Have about 8-9 fish (all healthy and established) and yellow polyps which seem to be doing very well. I have tried adding some corals (torch coral, open brain coral, mushroom corals, sarcophyton leather and yellow leather, trumpet coral and one bubble tip anemone) this was split into two time frames; not added all at once. All of these new additions eventually dies in about 7-14 days. The water tests perfect: salinity 1.020, pH 8.3-4, calcium 435, alkalinity of 350ppm, adding iodide, magnesium, calcium, strontium in modest amounts every week. I'm puzzled why I'm not having sucess with new corals. Suspecting that lighting is too intense?? Can someone help me? |
05/07/2010, 08:38 AM | #2 |
Moved On
Join Date: Apr 2010
Location: canada, toronto
Posts: 8,161
|
when I ran MH lighting, I had the same Issue, but then when introducing new corals, I used to place them really low and move them up day by day (as most softies are stored under T5s at most in LFS so a change to MH is too much stress for them.
you could alternativly move the lighting higher and move closer daily, cut the photo period to a couple hours and increase daily, or use eggcrates to diffuse some of the light and move that out eventually. in general, I never had success with MH and switched to all T5HO less heat, better coloration, and no accilimation |
05/07/2010, 09:42 AM | #3 |
Registered Member
Join Date: Jul 2007
Location: Orange County CA
Posts: 3,819
|
Well if your salinity is 1.020 this is to low for corals. This is partially the reason they die. Your alk is also way to high. An alkalinity of 350ppm=19.5dkh or 7meq/l is way to high. You need to lower the alk to 150-175ppm. This should fix your problem. Lighting may be an issue, but some of the water parameters you listed are not correct. Stop dosing without measuring first. Bring the salinity slowly to 1.0264 or 35ppt by topping off with salt water. How are you measuring salinity?
|
05/07/2010, 11:02 AM | #4 |
Registered Member
|
HQI bulbs are shielded by some form of tempered glass?
__________________
George Current Tank: Jan 2010, Custom Cadlights 65g Starfire Shallow Rimless (36"x24"x17") with 24g Sump, ATI Sunpower 6x39w, Aquamaxx ConeS CO 1, Vortech MP40 + MP10, Return Eheim 1260 |
05/07/2010, 12:24 PM | #5 |
Registered Member
Join Date: Apr 2005
Location: Lexington, KY
Posts: 2
|
Thanks for suggestions!
I will raise salinity slowly...I measure with a refractometer. Will also try diverting light. Also, thanks for information concerning alkalinity; adjustment will be made. Any other, helpful comments are welcome and appreciated.
|
05/07/2010, 12:36 PM | #6 | |
Registered Member
|
Not recommending diverting per se if this is related to my post, looking to ensure you have a piece of tempered glass in front of the HQI lights as I thought that was necessary with DE bulbs to block UV and prevent livestock burning.
Quote:
__________________
George Current Tank: Jan 2010, Custom Cadlights 65g Starfire Shallow Rimless (36"x24"x17") with 24g Sump, ATI Sunpower 6x39w, Aquamaxx ConeS CO 1, Vortech MP40 + MP10, Return Eheim 1260 |
|
05/07/2010, 01:20 PM | #7 | |
Moved On
Join Date: Apr 2010
Location: canada, toronto
Posts: 8,161
|
Quote:
I'm sure the Issues is from the water chemistry, not the light. follow what others said also, high concentration of Iodine and MG could be toxic ! so test before adding or if you cant test it, dont add it, do more water changes instead. |
|
05/07/2010, 06:51 PM | #8 |
Registered Member
Join Date: Jul 2007
Location: Orange County CA
Posts: 3,819
|
Iodine is not a necessary additive. It will do fine with normal water changes. If you want to divert the light you can get a fluorescent light panel. I use one myself and it works well.
|
05/08/2010, 03:18 PM | #9 | |
Registered Member
Join Date: Jan 2009
Location: Battle Creek, MI
Posts: 274
|
Quote:
__________________
tan Arte realmente vida de imatate de doese Current Tank Info: 48x18x21, 30g refugiuam/sump, (2) 250 w MH and 4 65w DC, Aqua Euro USA skimmer, 2 MP 40, quite one return pump 750 gpm, |
|
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HQI MH burn on corals? | MACJMC | Arizona - Fish & Reef Aquarium Group (FRAG) | 15 | 02/03/2009 03:16 PM |
Help...Is It Possible To "Sun"-Burn Soft Corals & Anemone? | FlyinggFish | Reef Discussion | 4 | 07/09/2008 10:44 PM |
Is It Possible To "Sun" Burn Your Corals and Anemone? | FlyinggFish | New to the Hobby | 5 | 07/09/2008 07:21 PM |
HELP My HQI lights are burning up | vwluv10338 | Lighting, Filtration & Other Equipment | 11 | 02/01/2007 10:14 PM |
HQI bulb burn in question | Waxxiemann | Lighting, Filtration & Other Equipment | 4 | 10/29/2006 01:33 AM |