|
05/04/2012, 07:47 AM | #1 |
Registered Member
Join Date: Feb 2010
Location: West Fargo, ND
Posts: 2,161
|
Programming: ATO Empty notification
Hello, I want to program an outlet on my apex to do the following.
I'm going to place a set of float switches in my top off bucket at the bottom. I'm going to plug the switches into an outlet on my apex. When the water is empty in the top off bucket I want the apex to detect that the switch is changed status and email me that the top off bucket is about empty. Anyone have a suggestion how I would do that. Would the Apex detect if the switch is open or closed based on the switch plug in being in the outlet or would I have to have something plugged into the switches to show a power draw? Thoughts? I have a spare set of float switches from autotopoff.com I want to use for this. Thanks, |
05/04/2012, 07:50 AM | #2 |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
What EXACTLY do you have from autotopoff.com? Just plain float switches, or one of their ATO controllers?
|
05/04/2012, 09:50 AM | #3 |
WHO DAT??
Join Date: Sep 2009
Location: Baton Rouge, LA
Posts: 5,709
|
You should read/study the chapter in the User Guide on switches and the breakout box. Floats and any other type of continuity switch don't get connected to outlets. They terminate into a breakout box of some kind which in turn is connected to a special jack on the controller or one of the expansion modules.
__________________
I don't work for Neptune. Please put all questions into forum posts and not PM's. Visit the Neptune Community Forums for the latest Neptune updates - forum.neptunesystems.com |
05/04/2012, 10:09 AM | #4 |
Registered Member
Join Date: Feb 2010
Location: West Fargo, ND
Posts: 2,161
|
Just the basic float switches. Not the ATO controller. I had been told I could use basic float switches to signal when some thing is empty or full. I wasn't sure how this was done through electricity... Maybe it's not?
|
05/04/2012, 10:47 AM | #5 |
Registered Member
Join Date: Apr 2012
Posts: 373
|
You need the Neptune breakout box. That will detect your float switches. Upto 6 for each breakout box.
Ato_Jug(virtual outlet) If switch1 closed then on Defer 1:00 then on If switch1 open then off Sump_low ( virtual) If switch2 closed then on Defer 1:00 then on If switch2 open then off Ato_Pump Fallback off Set off If outlet Ato_jug = on then off If sump_low = on then on Defer 20:00 then on Email alert If outlet Ato_jug = on then on That should Do it. |
05/04/2012, 11:47 AM | #6 |
Registered Member
Join Date: Apr 2012
Posts: 373
|
You need the Neptune breakout box. That will detect your float switches. Upto 6 for each breakout box.
Ato_Jug(virtual outlet) If switch1 closed then on Defer 1:00 then on If switch1 open then off Sump_low ( virtual) If switch2 closed then on Defer 1:00 then on If switch2 open then off Ato_Pump Fallback off Set off If outlet Ato_jug = on then off If sump_low = on then on Defer 20:00 then on Email alert If outlet Ato_jug = on then on That should Do it. |
05/04/2012, 01:59 PM | #7 |
WHO DAT??
Join Date: Sep 2009
Location: Baton Rouge, LA
Posts: 5,709
|
The float switches are just normal "dry" contact switches. They complete a circuit when closed and break the circuit when open. There's no voltage flowing through those wires - the system just detects continuity (or the lack of).
Because of this you can use not only float switches but a doorbell, magnetic window/door alarm switches, water sensors that are dry contact...just about anything that's normally open or closed (NO/NC). There's lots of applications for these type switches and they all will work on the controller.
__________________
I don't work for Neptune. Please put all questions into forum posts and not PM's. Visit the Neptune Community Forums for the latest Neptune updates - forum.neptunesystems.com |
05/08/2012, 09:26 AM | #8 |
Registered Member
Join Date: Feb 2010
Location: West Fargo, ND
Posts: 2,161
|
Thanks Alan. So, Alan, you're saying a break out box is not needed. If the switch is on, the Netptune outlet detects that the switch is making contact?
|
05/08/2012, 09:31 AM | #9 |
WHO DAT??
Join Date: Sep 2009
Location: Baton Rouge, LA
Posts: 5,709
|
No, you need the BoB or something similar DIY'd. Reason is you have up to 12 little wires coming from various switches, floats, whatever. Getting all of those back to the controller with little connectors and jacks would make the controller three times larger than it is. To get around that problem, the BoB was invented and works kind of like a consolidator of these wires. Those 12 wires (6 switches x 2 wires each) terminate in the BoB and in turn, one wire comes in from the BoB to the controller. Plus, this gives you the option to put the BoB (cheap) inside your stand with all that humidity and water and keep the controller (expensive) outside and far away. That's all the BoB does.
__________________
I don't work for Neptune. Please put all questions into forum posts and not PM's. Visit the Neptune Community Forums for the latest Neptune updates - forum.neptunesystems.com |
05/08/2012, 03:03 PM | #10 |
Registered Member
Join Date: Apr 2012
Posts: 373
|
Breakout box is nice and tidy. 40 bucks on aquacave. Well worth it. Here it is with 5 floats connected. I used thermostat wires To extend float switch wires
ImageUploadedByTapatalk1336510999.909754.jpg |
05/11/2012, 09:12 AM | #11 |
Registered Member
Join Date: Feb 2010
Location: West Fargo, ND
Posts: 2,161
|
Thanks guys. This makes more sense now to me.
|
05/11/2012, 10:35 AM | #12 | |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
Quote:
|
|
|
|