|
04/10/2012, 12:13 PM | #1 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
Programming Apex With Separate ATO
had an issue last night where i had my entire top off reservoir get pumped onto the floor.
the little tube from the aqualifter pump got loose and it was pumping onto the floor all night. was just wondering if there is a way for me to program my apex so that the plug only turns on for about 2 or 3 min every hour. if so, how could i do this? OR is there a way i can get the plug to turn off a couple min after the ATO starts drawing current for the pump? and then maybe have it reset after an hour to allow it to turn on again |
04/10/2012, 12:49 PM | #2 |
Registered Member
Join Date: Jul 2011
Location: WA / BC
Posts: 91
|
Right now is your ATO controlled via being plugged into an Apex outlet and a float switch? If so I assume you are turning the outlet on when the float switch changes from normal state, correct?
|
04/10/2012, 04:28 PM | #3 |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
You can easily do so... use the OSC command.
But first I suggest you directly address the problem... weight the end of the tubing or affix it somehow so it doesn't easily get pulled out. An airstone makes a nice little weight for airline tubing. Drill it through longitudinally so water flows smoothly. |
04/10/2012, 05:30 PM | #4 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
yes im using an avast marine ATO
it has a pressure switch that activates a plug. and i have the plug unit plugged into my apex |
04/10/2012, 06:22 PM | #5 |
WHO DAT??
Join Date: Sep 2009
Location: Baton Rouge, LA
Posts: 5,709
|
Been there,, done that! Had the same thing happen so don't feel bad. Like Russ said, takes 5 minutes and a couple pieces of velcro to fasten the outlet tube to something so it can't flop out of your sump. Do that before you fool with a program that may/may not catch the problem again.
__________________
I don't work for Neptune. Please put all questions into forum posts and not PM's. Visit the Neptune Community Forums for the latest Neptune updates - forum.neptunesystems.com |
04/10/2012, 06:29 PM | #6 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
thanks guys. but the problem wasnt that the tube fell out the sump (i have it zip tied in there)
the problem is that the tube fell out of the outlet side of the pump |
04/10/2012, 06:44 PM | #7 |
Registered Member
Join Date: Jul 2011
Location: WA / BC
Posts: 91
|
I am not overly familiar with the Avast ATO system but from pictures and what you are describing it sounds like the Apex has an Avast unit plugged into it and the Avast outlet is controlled by the Avast switch, does this sound correct? If so I'm guessing your Apex programming for the outlet in question is something like:
Fallback ON Set ON ... and that's it. Is this the case? If the Avast unit is regulating when the ATO runs instead of the Apex then you will not be able to control the outlet using the Apex as the state of the outlet (on or off) is governed by the Avast switch, relay and outlet. Please post your outlet programming if possible if there seems to be more to it than what I provided above. |
04/10/2012, 06:46 PM | #8 | |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
Quote:
|
|
04/10/2012, 06:50 PM | #9 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
heres the program i have it on right now
Fallback ON Set OFF OSC 057:00/003:00/000:00 Then ON it wont prevent flooding, but at least it wont be pumping water all night |
04/10/2012, 07:04 PM | #10 |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
That should work nicely, Marko.
|
04/10/2012, 07:08 PM | #11 |
Registered Member
Join Date: Jul 2011
Location: WA / BC
Posts: 91
|
That would work, however it should be noted that if the Avast unit is switching its own outlet it would be possible for the Apex to be on and the Avast float switch / outlet to be off and vice versa.
This shouldn't be a problem as long as the water that can evaporate from your tank in an hour could be replenished within 3 minutes using the aqualifter circuit. |
04/10/2012, 09:42 PM | #12 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
yeah i think it'll be just fine. ill adjust it if needed
|
04/10/2012, 10:28 PM | #13 |
Registered Member
Join Date: Feb 2012
Posts: 59
|
Shouldn't you fallback be off ?
|
04/10/2012, 10:33 PM | #14 |
Registered Member
Join Date: Mar 2011
Location: Alberta Canada
Posts: 93
|
|
04/11/2012, 05:10 AM | #15 |
Registered Member
Join Date: Jan 2007
Location: El Cajon, CA
Posts: 7,818
|
|
04/11/2012, 09:44 AM | #16 |
Registered Member
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 8
|
Here's my program to help deal with stuck float switch but it should help in your situation too. My ato pump comes on after every 4hrs and allow to run up to 20sec only (my pump needs less than 20sec to topoff but your pump speed might vary). If the pump runs for more than 20sec, I will get a text message telling me it exceeded the time limit which probably means I have a stuck float switch or in your case a loose hose. Hope this helps.
[ATOSUMP] Set OFF If Outlet SumpATO_SW = ON Then ON If Outlet ATOTimer_sw = ON Then OFF If Outlet ATOLow_SW = ON Then OFF Min Time 240:00 Then OFF [ATOTimer_sw] Set OFF If Outlet ATOSump = ON Then ON Defer 000:20 Then ON Last edited by ISeaReef; 04/11/2012 at 09:55 AM. |
Thread Tools | |
|
|