|
01/25/2019, 02:19 PM | #1 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Some PCB design ideas for DIY LDD-L driver based builds
Just in case anybody finds these interesting, after building some larger scale LED setups for a couple propagation and fishroom setups I've been wanting something different than the usual offerings from places like Coralux, Steve'sLED, RapidLED, etc. All of the boards you see offered for sale work for lower voltage builds (12-24 volts) just fine, but the LDD-L drivers are compact, easy to use alternatives to the LDD-H series for smaller builds, or when multiple smaller strings are required. I for one use them extensively for nano fixtures, or for filling in the extra colors on "full spectrum" types of builds, in conjunction with 21 volt laptop power supplies, ranging in size from 3 to 7 amps, which is plenty in most smaller to medium situations.
These can be jumpered to allow channels to be doubled up, to allow four or eight channels of control on the eight driver version, and eight channels of control on the sixteen channel version, with daisy chaining also possible for stacking boards as needed for larger scale configurations. All parts are through-hole, so easy enough for even a novice to solder up Keep in mind these are sort-of a power-user board, and while they offer pretty good flexibility, they are not as of now compatible with the Bluefish mini- although with the use of a level shifter they would be, the fullsize Bluefish will work however. I have been primarily using the LDD-L with the Storm controller or the very nice 16 channel controller featured over at Ultimatereef- https://www.ultimatereef.net/threads...roller.784531/ Any controller using the PCA9685 PWM driver would be a perfect fit for a companion to this board. I'm also working up some sketches for larger versions using the LDD-H drivers as well, but due to the larger physical size I'm not sure I'll put more than eight drivers to a single board to keep them affordable for small runs of PCBs. Suggestions are welcome.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/25/2019, 08:54 PM | #2 |
Registered Member
Join Date: Apr 2013
Posts: 1,793
|
I'm going to "implore" you to make the 10k pulldowns jumperable...
|
01/26/2019, 06:41 PM | #3 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Well, I figured I could do as much, especially for you
Here's the Nano version, meant for small rigs or supplemental lighting on larger systems, can be set up for four channels (with jumpers to run as two channels) and the proof of concept for the jumper addition. I'm thinking a big jumper block for the larger boards, or even DIP switches may not be a bad idea, as having it all at the input connector may prove a bit crowded or confusing. I started a thread over at the "other site" (damn interboard censorship ) too, and it seems discussion has picked up on it over there a bit more!
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/26/2019, 09:00 PM | #4 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
For anybody who cares, these are an open source design, once things are finalised the files will be open to free use by anyone interested!!!
Here's the first iteration of the "EZ" Nano board, onboard DC power and 1/8" TRS (stereo) jacks, so that all one needs to do is drill corresponding holes in the panel and allow the TRS jacks to protrude slightly, and then insert power. I'll work up a drilling template too (easy peasy) to make it easy enough to use. Sure beats air-wiring things on small fixture builds! Since this is the "EZ" version, I've left off the jumpering feature to allow it to be a very simple board, if one wishes to parallel channels they would need to do some jumpering of their own, or go with the "Pro" version of the board. The DC jack chosen- Kobiconn 163-179PH-EX: https://www.mouser.com/ProductDetail...5l2UOaIqcGCw== The TRS/stereo jack chosen- CUI SJ1-3533: https://www.mouser.com/ProductDetail...0TSYIwwZxYnQ== If anyone knows of any alternatives that may be cheaper/preferable for similar quality let me know.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/28/2019, 06:00 AM | #5 |
Registered Member
Join Date: Apr 2006
Location: Malta
Posts: 22
|
Hi,
Great project. Do you think that these could also be used for LDD-H? Thanks |
01/28/2019, 06:01 AM | #6 |
Registered Member
Join Date: Apr 2006
Location: Malta
Posts: 22
|
LDD-700H to be more precise
|
01/28/2019, 07:47 AM | #7 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Not these ones, but after I'm happy with these I'll start on versions for the LDD-H series as well. They are physically much larger, so only half as many are likely to fit in a given board size. Complete new design will be needed due to the differences.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/29/2019, 11:32 AM | #8 | |
Registered Member
Join Date: Jan 2014
Location: Robin hood country, UK
Posts: 817
|
Quote:
Tim |
|
01/29/2019, 11:39 AM | #9 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Hopefully some people will be interested in some! I'll probably do a handful of each for myself at least. Getting the drivers lashed up neatly is the biggest hurdle I usually face, as once that's done a suitable case is much easier to figure out, especially if retrofitting to an existing rig, or doing it in a distributed setup for more complex applications
The EZ Nano is my favorite so far, should make it easier for the small tank builds to have the same functionality as the big boys, without so many compromises. The majority of my personal setups have been smaller by necessity, so having a nice compact solution is a godsend compared to huge LDD-H PCBs when you don't need or want the higher voltage string capability. Even my 5.5 gallon freshwater planted has four channels of control! For less than a dozen LEDs! The drivers take up more space than the emitter stars do.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/29/2019, 11:49 AM | #10 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
EZ Nano and EZ8 now feature solder bridge functionality so that solder blob jumpers can be fitted (or 0R 0805 SMD resistors if you're anal) to jumper the boards for 2 (nano) or 4/6 (on the 8) channels, respectively.
Also changed the ouput silkscreening so it makes more sense
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. Last edited by lingwendil; 01/29/2019 at 12:36 PM. |
01/30/2019, 12:26 PM | #11 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Ok, now I'm happy with the Nano and 8UP pro, looks nice and tidy, and optimized the jumper traces. Each channel can be jumpered on/off, adjacent channels can be connected in parallel, and SMD resistors can be used. I like it.
Going to tidy up the EZ versions next.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/31/2019, 05:16 AM | #12 |
Registered Member
Join Date: Apr 2006
Location: Malta
Posts: 22
|
Looks nice
|
01/31/2019, 08:39 AM | #13 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Ok, now I'm happy with the Nano Pro, 8UP Pro, and EZ Nano versions. I'm having a heck of a time figuring out a good way to do the on/off jumpers for the 8UP EZ, as it's a little cramped on there! I'll have to get creative with scooting parts around.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/31/2019, 12:46 PM | #14 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Alright, got the boards to a mostly final state for the 4 and 8 channel versions. Attached are the current board designs for the Nano PCBs.
So far this has been a very enjoyable (and challenging!) project, and I'm very pleased with the boards so far. We have standard functionality across all four, with similar layout and schemes to make them easy to understand as well as making upgrades easy when moving from one to the next. Small too! The nano versions are 50mm (2") square, and the 8Up boards are 50x100mm (2x4") for nice compact builds. Now we just need a cool logo or symbol of some sort to silkscreen onto them
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
01/31/2019, 12:47 PM | #15 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
And here are the 8Up versions-
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
02/02/2019, 11:14 AM | #16 |
Registered Member
Join Date: Jan 2014
Location: Robin hood country, UK
Posts: 817
|
Look very nice
Question - what does it say above your email address? Tim |
02/02/2019, 06:26 PM | #17 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
"Lingwendil"
It's the moniker I took for myself. I'm a huge fan of Tolkien, and it means "fish friend" in Quenya, the high-elvish (or "elf-latin" as some say) language from the Lord of the Rings and related series. It's written in the alphabet ("Tengwar") used throughout the various works Tolkien wrote. (yes, I'm a colossal nerd )
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
02/03/2019, 06:09 AM | #18 |
Registered Member
Join Date: Jan 2014
Location: Robin hood country, UK
Posts: 817
|
Nowt wrong with a bit of Tolkien! Tim |
02/07/2019, 12:54 PM | #19 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Ok, here we go! here are the (tentative) final versions of the 4 and 8 channel boards!
All boards can be jumpered to turn on/off each driver, and each board features jumpers to allow running channels in parallel. Might have a small graphic of some sort added and then it's likely off to production, and files will be posted once it passes the sniff test. Also, the 8up boards should slot into a Makers sink upper rails nicely once finished
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
02/07/2019, 03:34 PM | #20 |
Registered Member
Join Date: Jan 2014
Location: Robin hood country, UK
Posts: 817
|
Look very nice! Once you've released the files, might have to get a few of them done myself
Tim |
02/08/2019, 08:39 AM | #21 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
I'm just giving it a few days to see if there are any last minute ideas, and maybe a graphic, then I'll finish them out and order some. I'm also going to panelise the pro boards so that four nanos each, or two 8ups will fit to a 100mm square outline, making them quite affordable in small quantities. Buy a set, and give a few away to your friends sort of deal
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
02/08/2019, 03:31 PM | #22 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Well, started on the LDD-H boards, started on the eight driver version, and have it mostly how I want it. Going to finesse the details a bit, and then when it's finalized I'll whittle it down to a four channel version as well.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. Last edited by lingwendil; 02/08/2019 at 03:48 PM. |
02/10/2019, 12:05 PM | #23 |
Registered Member
Join Date: Apr 2006
Location: Malta
Posts: 22
|
Hi,
It has been a while since I printed my old boards, however I think that I would need an eagle file right? Can you share this? |
02/10/2019, 12:06 PM | #24 |
Registered Member
Join Date: Apr 2006
Location: Malta
Posts: 22
|
Thanks a lot for the great design
|
02/10/2019, 08:59 PM | #25 |
Man who sold the world
Join Date: Oct 2004
Location: Oakley, behind enemy lines in communist occupied California.
Posts: 254
|
Yup. I'll share all the files once I've declared them done, hopefully sometime this week. I'll be doing a four channel LDD-H version as well, and I'm planning one that will take a bluefish mini directly plugged to the board.
__________________
LED snob. Unapologetic Luxeon Rebel and Bridgelux Vero fanboy. Every time a fluorescent or halide fixture is scrapped, an angel gets its wings. |
Thread Tools | |
|
|