Reef Central Online Community

Go Back   Reef Central Online Community > General Interest Forums > New to the Hobby
Blogs FAQ Calendar Mark Forums Read

Notices

User Tag List

Reply
Thread Tools
Unread 11/10/2017, 08:26 AM   #1
NanoReefNoob
Registered Member
 
NanoReefNoob's Avatar
 
Join Date: Aug 2011
Location: Yuma, AZ
Posts: 241
Bottom trim

Hey yawl,

I found a 150G with the bottom trim for sale for supper cheap and bought it. Is this bottom trim needed for any ki d of integrety to the tank or just for show. It is just the bottom brace that the tank sits on.


Attached Images
File Type: jpg FB_IMG_1510323757570.jpg (29.7 KB, 42 views)
File Type: jpg FB_IMG_1510323769416.jpg (33.6 KB, 36 views)
__________________
This is only a hobby if you are having fun, ether wise it is work.

Current Tank Info: 72G fresh water, Reef tank build in progress.
NanoReefNoob is offline   Reply With Quote
Unread 11/10/2017, 08:43 AM   #2
Shamous113
Registered Member
 
Shamous113's Avatar
 
Join Date: Nov 2015
Location: Ontario, Canada
Posts: 81
I'd replace it. I've heard these guys are a good place to order from.


__________________
Current tank: 150gal mixed reef display w/120gal basement sump
Shamous113 is offline   Reply With Quote
Unread 11/10/2017, 08:45 AM   #3
mcgyvr
Registered Member
 
mcgyvr's Avatar
 
Join Date: Sep 2003
Location: North Carolina
Posts: 20,050
That one concerns me a bit and I wouldn't use it as is without replacing the trim (fairly easy/cheap task)..
The bottom trim isn't so much structural but it does help alleviate pressure points on the glass,etc..
I would remove it and replace its functionality with a new trim or similar..


__________________
Who me?
mcgyvr is offline   Reply With Quote
Unread 11/10/2017, 02:45 PM   #4
Jeramirez85
Registered Member
 
Join Date: Nov 2008
Location: Houston
Posts: 50
I would change out the trim. It will help to even out the pressure the tank will be in when full


Jeramirez85 is offline   Reply With Quote
Unread 11/16/2017, 10:34 AM   #5
nanosteve309
Registered Member
 
Join Date: Feb 2017
Posts: 62
I would remove it. As far as pressure points are concerned I would rather have the entire bottom of the tank sitting flush as opposed to 1/2" (If that) pressure points around the tank.


nanosteve309 is offline   Reply With Quote
Unread 11/16/2017, 10:43 AM   #6
nanosteve309
Registered Member
 
Join Date: Feb 2017
Posts: 62
Figure a gallon of water weighs 8.34 pounds.. at 150 gallons that is 1248lbs.

Lets assume the tank in question is 24"H X 72"L X 18"D. If the tank were to sit with the entire bottom flush to the stand then the 1248lbs of water would be distributed among 1296in^2. So roughly a lb of water per square inch.

If the tank were to sit on a 1/2" trim outlining the bottom of the tank about 41in^2 would take a majority of the water load.


nanosteve309 is offline   Reply With Quote
Unread 11/17/2017, 12:24 PM   #7
billdogg
Registered Member
 
billdogg's Avatar
 
Join Date: Apr 2008
Location: Grove City, Ohio
Posts: 10,806
I would not use a tank that was designed with a frame without said frame. There is a reason it was put on in the first place, and I have no desire to do a leak/stress test with 150g of saltwater in my living room.

Could it be just fine? Sure. Just not in my house.


__________________
I'll try to be nice if you try to be smarter!
I can't help that I grow older, but you can't make me grow up!

Current Tank Info: 120 mixed reef with 40b sump, RO 150 skimmer, AI Sol Blue x 2, and a 60g Frag Tank with 100g rubbermaid sump. 2 x Kessil A360w lights, BM curve 5 skimmer
billdogg is offline   Reply With Quote
Unread 11/17/2017, 12:47 PM   #8
sde1500
Registered Member
 
sde1500's Avatar
 
Join Date: Mar 2015
Location: Glocester, RI
Posts: 3,336
If it had trim, it needs the trim. I would absolutely have it replaced.


__________________
My build thread:

http://reefcentral.com/forums/showthread.php?t=2548422

Current Tank Info: 65 gallon mixed reef, Eshopps sump and HOB overflow, RO-110int skimmer, Reefbreeder 32" photons V1.
sde1500 is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -6. The time now is 11:48 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2024 Axivo Inc.
Use of this web site is subject to the terms and conditions described in the user agreement.
Reef CentralTM Reef Central, LLC. Copyright ©1999-2022
User Alert System provided by Advanced User Tagging v3.3.0 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.