radion xr30w pro fan dead

teo241 · 07/15/2017, 11:19 AM

Discovered the above light off this morning -- LED on top alternating between red and I think yellow. When I reset it same issue.

Dead fan? It does have some build up on it, dust/a bit of salt.

I took the cover off, disconnected the fan and hooked up a small battery tester with 2 AAs to try and get it to run, it won't.

Is there a way to fix this myself? replacement fan? Does it have to be sent in?

Thanks.

teo241 · 07/15/2017, 12:09 PM

well scratch that. connected the fan to a 9V battery and it works fine.

so no idea what is wrong with the unit.

teo241 · 07/15/2017, 01:49 PM

Solved my own issue. Three hours I'll never get back. Had to connect the light directly to my computer and reset the firmware. Reeflink wouldn't do it. Connecting it to the reeflink via USB wouldn't do it. Really shouldn't be this difficult.

mjc0760 · 08/10/2017, 10:04 AM

Quote:

Originally Posted by teo241

Solved my own issue. Three hours I'll never get back. Had to connect the light directly to my computer and reset the firmware. Reeflink wouldn't do it. Connecting it to the reeflink via USB wouldn't do it. Really shouldn't be this difficult.

My G3s seem to work fine, i.e., never had one shot down from overheating, but one fan is always on and the other is NEVER on. I have not pulled the fan out to check it (and don't really want to). I'm running them through the Apex WXM module... you think this is just a firmware issue? i'm headed to the Neptune Apex forum next to see if there is a solution there.

mjc0760 · 08/10/2017, 03:44 PM

Update - - After updating the Radion firmware (via the Apex) the fan is still not working.

teo241 · 08/15/2017, 07:46 AM

If it were me I'd pull the fan out, just a few screws for the cover, it then pops off. (if you need there are videos on youtube).

The fan isn't screwed in, you just have to pop off a small connector.

To test it I used a 9 volt battery and two wires.

mjc0760 · 08/24/2017, 03:53 PM

I'll give that a try... thanks!

PAreefGUY · 08/24/2017, 04:02 PM

Call Ecotech, they can check your light through your reeflink.

mjc0760 · 11/11/2017, 11:17 AM

I finally got around to opening up the XR30 and have mixed emotions about what I found. The good news is that it was a simple fix - - only one of the two pins was connected to the fan. The other was bent down and the opening for the pin was smashed closed. I bent the pin up into place, used a needle to open up the hole on the connector and viola... she works! The sad part is that this problem actually escaped detection in EcoTech’s QA/testing before boxing this (very expensive) light up. This should have never shipped like this. Oh well, it’s fixed now and I can crank up the intensity without worrying about overheating.

teo241 · 11/11/2017, 04:28 PM

Quote:

Originally Posted by mjc0760

I finally got around to opening up the XR30 and have mixed emotions about what I found. The good news is that it was a simple fix - - only one of the two pins was connected to the fan. The other was bent down and the opening for the pin was smashed closed. I bent the pin up into place, used a needle to open up the hole on the connector and viola... she works! The sad part is that this problem actually escaped detection in EcoTech’s QA/testing before boxing this (very expensive) light up. This should have never shipped like this. Oh well, it’s fixed now and I can crank up the intensity without worrying about overheating.

I had a similar experience with my reef genesis water change system. One of the holding cylinders wouldn’t open it’s valve to drain when running. I opened it up and I found one of the wire connectors on the inside wasn’t attached. Pushed it on and it works. Sent an email to the company and didn’t even get a response.

Sent from my iPhone using Tapatalk

07/15/2017, 11:19 AM	#1
teo241 Registered Member Join Date: Feb 2003 Location: wisconsin Posts: 339	radion xr30w pro fan dead Discovered the above light off this morning -- LED on top alternating between red and I think yellow. When I reset it same issue. Dead fan? It does have some build up on it, dust/a bit of salt. I took the cover off, disconnected the fan and hooked up a small battery tester with 2 AAs to try and get it to run, it won't. Is there a way to fix this myself? replacement fan? Does it have to be sent in? Thanks. __________________ 360, 75, 45

07/15/2017, 12:09 PM	#2
teo241 Registered Member Join Date: Feb 2003 Location: wisconsin Posts: 339	well scratch that. connected the fan to a 9V battery and it works fine. so no idea what is wrong with the unit. __________________ 360, 75, 45

07/15/2017, 01:49 PM	#3
teo241 Registered Member Join Date: Feb 2003 Location: wisconsin Posts: 339	Solved my own issue. Three hours I'll never get back. Had to connect the light directly to my computer and reset the firmware. Reeflink wouldn't do it. Connecting it to the reeflink via USB wouldn't do it. Really shouldn't be this difficult. __________________ 360, 75, 45

08/10/2017, 03:44 PM	#5
mjc0760 Registered Member Join Date: Feb 2015 Location: Robbinsville NJ Posts: 98	Update - - After updating the Radion firmware (via the Apex) the fan is still not working. __________________ Aqueon 90g RR, Trigger Systems Emerald 34 sump, 2 Radion XR30w G3 PROs, Vertex Omega 150 Skimmer, MaxSpect Gyre XF130 and XF230, Sicce Syncra Silent 4.0 Return, Apex Controller, Avast ATO, BRS Media R Current Tank Info: 90 gallon mixed reef

08/15/2017, 07:46 AM	#6
teo241 Registered Member Join Date: Feb 2003 Location: wisconsin Posts: 339	If it were me I'd pull the fan out, just a few screws for the cover, it then pops off. (if you need there are videos on youtube). The fan isn't screwed in, you just have to pop off a small connector. To test it I used a 9 volt battery and two wires. __________________ 360, 75, 45

08/24/2017, 03:53 PM	#7
mjc0760 Registered Member Join Date: Feb 2015 Location: Robbinsville NJ Posts: 98	I'll give that a try... thanks! __________________ Aqueon 90g RR, Trigger Systems Emerald 34 sump, 2 Radion XR30w G3 PROs, Vertex Omega 150 Skimmer, MaxSpect Gyre XF130 and XF230, Sicce Syncra Silent 4.0 Return, Apex Controller, Avast ATO, BRS Media R Current Tank Info: 90 gallon mixed reef

08/24/2017, 04:02 PM	#8
PAreefGUY Registered Member Join Date: Feb 2006 Location: pennsylvania, USA Posts: 14	Call Ecotech, they can check your light through your reeflink.

11/11/2017, 11:17 AM	#9
mjc0760 Registered Member Join Date: Feb 2015 Location: Robbinsville NJ Posts: 98	I finally got around to opening up the XR30 and have mixed emotions about what I found. The good news is that it was a simple fix - - only one of the two pins was connected to the fan. The other was bent down and the opening for the pin was smashed closed. I bent the pin up into place, used a needle to open up the hole on the connector and viola... she works! The sad part is that this problem actually escaped detection in EcoTech’s QA/testing before boxing this (very expensive) light up. This should have never shipped like this. Oh well, it’s fixed now and I can crank up the intensity without worrying about overheating. __________________ Aqueon 90g RR, Trigger Systems Emerald 34 sump, 2 Radion XR30w G3 PROs, Vertex Omega 150 Skimmer, MaxSpect Gyre XF130 and XF230, Sicce Syncra Silent 4.0 Return, Apex Controller, Avast ATO, BRS Media R Current Tank Info: 90 gallon mixed reef