|
12/31/2017, 11:26 AM | #1 |
Registered Member
Join Date: Jul 2008
Location: State College PA USA
Posts: 251
|
Frag tank plumbing question
I purchased a 30 x20 x10 acrylic frag tank from a guy for a very good price. When I purchased it, I had some concerns about how it was drilled. the overflow is in the right hand corner and there is a hole drilled in the bottom for a 1" bulkhead. In the back of the overflow, there is a hole drilled for a 1/2" bulkhead. The guy said that I could use lockline and just run the return up and over the overflow. Technically, i could do that but I would prefer not to. I considered putting a 90 going up and using that as an emergency drain like in a herbie setup and either drilling another hole for the return or going over the top.
What do you all think? Would by emergency drain idea work or would there be an issue as the main drain is 1" and the emergency would be 1/2". I have attached a few pics to show what I am working with. Any suggestions are appreciated. Thanks in advance. |
01/01/2018, 11:34 AM | #2 |
Registered Member
Join Date: Jul 2008
Location: State College PA USA
Posts: 251
|
anyone??? I'm at a loss
|
01/01/2018, 12:46 PM | #3 |
Registered Member
Join Date: Dec 2015
Posts: 233
|
Why do you not want to run the locline out of the overflow? It would work as a Durso.
If you want to have an extra drain, you could use the second hole as a drain. I don't see the 1/2" being a problem if it is only an emergency. You would have to plug the main drain solid to have a problem. That being said, it is always safer to have the same size drain... You've got options. Sent from my Pixel XL using Tapatalk |
01/01/2018, 12:57 PM | #4 |
Registered Member
Join Date: Jul 2008
Location: State College PA USA
Posts: 251
|
dt204..thanks for your response. Would I just run up and over the overflow? I didn't know if that would be an issue. If not, I will go that route. I will have to see if I have enough lock line lying around. lol
|
01/01/2018, 08:33 PM | #5 |
Registered Member
Join Date: Dec 2015
Posts: 233
|
I have mine as rigid up to the top of the overflow, and then locline over the weir. I have a small hole drilled in the locline for a syphon break as well. And I keep the output fairly high up as another failsafe.
The Durso is a basic method of plumbing, and works great. It just doesn't have the safety of a bean animal for instance. You can see I have a float switch in my overflow area as an extra safety with my Durso. I'd pour over the forums for a few hours and check out different builds and plumbing threads to see what you like best, and what might work best for your situation. Sent from my Pixel XL using Tapatalk |
01/01/2018, 09:03 PM | #6 |
Registered Member
Join Date: Jul 2008
Location: State College PA USA
Posts: 251
|
I have looked at a lot of posts on here but haven't been able to find a tank quite like mine. Thank you for posting the pics.
here is what i have mocked up. I haven't drilled a hole in the top of the durso yet or removed a few teeth in the weir. Where did you drill the hole for the siphon break? How does it look? |
01/01/2018, 09:11 PM | #7 |
Registered Member
Join Date: Jul 2012
Location: Medina oh
Posts: 1,782
|
That should work. I would prefer a straighter run,but there doesn’t look like there is room.
|
01/01/2018, 09:14 PM | #8 |
Registered Member
Join Date: Jul 2008
Location: State College PA USA
Posts: 251
|
rocsec1- that was my main concern. I thought about not putting the elbow on the drain and running full siphon but that would not be wise hahahaha. I am considering putting another 1/2" elbow then running the locline of of that to get a straighter run.
|
Thread Tools | |
|
|