|
09/13/2017, 09:07 PM | #1 |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Jebao to apex
Those of you with the jebaos hooked to youre apex this is for you.
Im wanting to get 4 jebaos for 3 differebt tanks. I want all 4 to be controlled by my apex. I cant seem to figure out what ones can be hooked directly to the apex and what ones require the jebao to apex connections. PLZ HELP!!!!! Sent from my SAMSUNG-SM-G891A using Tapatalk |
09/13/2017, 09:24 PM | #3 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
Do you have any hooked up. Whts the newest one? Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/13/2017, 11:45 PM | #4 |
Registered Member
Join Date: Apr 2017
Posts: 16
|
It depends. The following is based on what i have read. I haven't verified.
You don't mention if you are looking at pumps or powerheads. For pumps the older models require what cheep reef mentions above. The newer models (dcp) will not work and require the aqlink a1. For powerheads supposedly the sw models (4 and up) can be connected directly to an apex. You'll need to make the cable, but it's straight forward. I just ordered a couple and will be trying them out this weekend. Ron |
09/14/2017, 10:03 AM | #5 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
I am looking for both my pumos and the new powerheads. Ill be ordering the powerveads soon. I think ill get 2 sw-4s abd 2sw-8s Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/14/2017, 10:05 AM | #6 | |
Registered Member
Join Date: Apr 2002
Posts: 1,076
|
Quote:
Which is exactly the same as the box I linked to just a bought item instead of a DIY mod, which is this. Jebao harness |
|
09/14/2017, 10:39 AM | #7 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/14/2017, 10:41 AM | #8 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/14/2017, 03:08 PM | #9 | |
Registered Member
Join Date: Apr 2017
Posts: 16
|
Quote:
See this video https://www.youtube.com/watch?v=U4UDkkeM5V8 Ron |
|
09/14/2017, 03:22 PM | #10 |
Registered Member
Join Date: Apr 2017
Posts: 16
|
Also I'm a little confused by the DIY cable as all it does is change the voltage from 0-10V to 0-5V.
I was under then impression that the WP-40's required a PWM signal (which the Apex does not provide as far as I know) and I thought that was what the purchased adapter referenced above did for you. What am I missing? |
09/14/2017, 04:23 PM | #11 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/18/2017, 04:49 PM | #12 |
Registered Member
Join Date: Apr 2017
Posts: 16
|
So I did not have good luck with the direct control using the SW controller. Just plugging in the DC connector (not connected to anything) seemed to break my controller. Very odd. I haven't investigated further. I ordered the Jebao-Apex Controller Adapter and will go that route instead. In the mean time I'll dig into the SW controller and see if I can figure out what got hosed.
|
09/19/2017, 03:32 PM | #13 | |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
Quote:
Sent from my SAMSUNG-SM-G891A using Tapatalk |
|
09/24/2017, 05:48 PM | #14 | |
Registered Member
Join Date: Apr 2017
Posts: 16
|
Quote:
Anyhow the other controller works great. At some point I'll pull apart the sw controller and try to figure out what happened. Ron |
|
09/26/2017, 09:22 PM | #15 |
Registered Member
Join Date: Oct 2006
Location: Coarsegold CA
Posts: 97
|
I run the power heads and a D.C. Pump direct to my power strip on the Apex. I control them with the jebao controllers but the feed time, on-off controls are through my Apex. The stock jebao controller remembers the settings as you switch it on and off.
|
09/27/2017, 04:07 PM | #16 |
Registered Member
Join Date: Dec 2016
Posts: 187
|
I run the adaptor module with my two, SW15 powerheads. Works like a charm.
__________________
125g long DT, RS-200 Sump, Reef Octo 150 Skimmer, Full apex automation *PS, I'm a newb so take my suggestions with a grain of reef salt* |
10/04/2017, 10:34 AM | #17 |
Registered Member
Join Date: Apr 2016
Location: Missouri
Posts: 214
|
I went ahead and went with the jebao to apex mods. Just incase eberyone was wondering.
They work great and i dont have to cut anything lol. Sent from my SAMSUNG-SM-G891A using Tapatalk |
09/30/2018, 01:38 PM | #18 |
Registered Member
Join Date: Jun 2002
Location: San Diego
Posts: 326
|
Anyone knows if it's supposed to work with the OW wavemaker series?
|
|
|