Need copies of Salifert CA and Alk instructions/scale

PhilipOSU · 12/19/2008, 05:23 PM

My copy's of these were thrown out this past week while my house was being cleaned. Does anyone have a copy they can email me? My email address is [email protected]

Thanks,
Phil

Cove Beach · 12/19/2008, 05:26 PM

Give me a few mins to scan them and i will send them to you.

PhilipOSU · 12/19/2008, 05:31 PM

Awesome...Thanks Cove

Cove Beach · 12/19/2008, 05:50 PM

Sent it 2 mins ago

PhilipOSU · 12/19/2008, 06:24 PM

Thanks, again Cove. Alk went from way high (13.4) two and a half weeks ago to 7.7 tonight. I need to get the new DIY Kalk reactor to quit leaking so I can drip kalk into the sump rather than on the basement floor...that should balance this out a bit.

Tswifty · 12/20/2008, 12:06 AM

Those darn MJ fittings... I wonder if savko could make a custom bushing for them or has a bushing that would have a tighter fit.

I guess I got lucky, I gooped that junk on and it sealed for me.

PhilipOSU · 12/20/2008, 10:50 AM

I actually have the MJ fitting sealed up now, but the JG bulkhead is leaking...I am going to the depot or lowes this afternoon and see if I can find a rubber washer to fit the bulkhead.

Cove Beach · 12/20/2008, 11:00 AM

Is the fitting you are calling a bulkhead, just JG on one side and pipe thread on the other? If so put at least 4-5 wraps of teflon tape on it. Thats what i usually do and have had no leaks.

sailoracu2 · 12/20/2008, 11:16 AM

Mark could you pm me a copy of the Alk instructions please. Thanks Jim

PhilipOSU · 12/20/2008, 11:32 AM

Mark, it is a bulkhead fitting from Savko. I bought a bunch of them for TJ and me and they didn't have the rubber seals.

12/19/2008, 05:23 PM	#1
PhilipOSU Registered Member Join Date: Feb 2008 Location: Canton, OH Posts: 535	Need copies of Salifert CA and Alk instructions/scale My copy's of these were thrown out this past week while my house was being cleaned. Does anyone have a copy they can email me? My email address is [email protected] Thanks, Phil

12/19/2008, 05:26 PM	#2
Cove Beach Registered Member Join Date: Jan 2006 Location: Sheffield Lake Posts: 1,278	Give me a few mins to scan them and i will send them to you. __________________ Patience, something my reef teaches me every day... 245 Reef Current Tank Info: 245 Star Fire display,Basement Sump system

12/19/2008, 05:50 PM	#4
Cove Beach Registered Member Join Date: Jan 2006 Location: Sheffield Lake Posts: 1,278	Sent it 2 mins ago __________________ Patience, something my reef teaches me every day... 245 Reef Current Tank Info: 245 Star Fire display,Basement Sump system

12/20/2008, 12:06 AM	#6
Tswifty Registered Member Join Date: Sep 2007 Location: PA Posts: 14,028	Those darn MJ fittings... I wonder if savko could make a custom bushing for them or has a bushing that would have a tighter fit. I guess I got lucky, I gooped that junk on and it sealed for me. __________________ "Enough light? Heck I could go barebottom and grow SPS in the stand!" - DiscoReefRover

12/20/2008, 11:00 AM	#8
Cove Beach Registered Member Join Date: Jan 2006 Location: Sheffield Lake Posts: 1,278	Is the fitting you are calling a bulkhead, just JG on one side and pipe thread on the other? If so put at least 4-5 wraps of teflon tape on it. Thats what i usually do and have had no leaks. __________________ Patience, something my reef teaches me every day... 245 Reef Current Tank Info: 245 Star Fire display,Basement Sump system

12/19/2008, 05:31 PM	#3
PhilipOSU Registered Member Join Date: Feb 2008 Location: Canton, OH Posts: 535	Awesome...Thanks Cove

12/19/2008, 06:24 PM	#5
PhilipOSU Registered Member Join Date: Feb 2008 Location: Canton, OH Posts: 535	Thanks, again Cove. Alk went from way high (13.4) two and a half weeks ago to 7.7 tonight. I need to get the new DIY Kalk reactor to quit leaking so I can drip kalk into the sump rather than on the basement floor...that should balance this out a bit.

12/20/2008, 10:50 AM	#7
PhilipOSU Registered Member Join Date: Feb 2008 Location: Canton, OH Posts: 535	I actually have the MJ fitting sealed up now, but the JG bulkhead is leaking...I am going to the depot or lowes this afternoon and see if I can find a rubber washer to fit the bulkhead.

12/20/2008, 11:16 AM	#9
sailoracu2 Registered Member Join Date: Mar 2008 Location: medina oh Posts: 569	Mark could you pm me a copy of the Alk instructions please. Thanks Jim __________________ Jim Current Tank Info: new build 65g with 35g basement sump and 20g frag tank

12/20/2008, 11:32 AM	#10
PhilipOSU Registered Member Join Date: Feb 2008 Location: Canton, OH Posts: 535	Mark, it is a bulkhead fitting from Savko. I bought a bunch of them for TJ and me and they didn't have the rubber seals.