Help with upgrading JBJ

HartfordWhalers · 02/25/2006, 01:28 PM

I just got a JBJ Nano 12g. I wanted to replace the pump so I just bought a Mini Jet 606 which people said would be good for this sized tank. I don't no how to get the power cord from the old pump out. It runs through the top of the hood. Shoould I cut it or is there some way of pulling it out without snaping anything

Thanks in Advance

~Andrew

This is a picture of what im talking about the cord goes through the top. Do i cut a little hole. I see the hole on the right i could run it through tehre but i still wanna get the other cord out of the chamber.
Alright the picture isnt working. I cant load it oto this site. Its over 50kb. I have tried about 100 times to makwe it smaller and smaller and by the size it will work you cant see it but if you have one plase help

jcatblum · 02/25/2006, 03:48 PM

sorry wish I could help..... I am sure someone can, did you look in the DIY forum?

kelleymmm1 · 02/25/2006, 04:44 PM

It sounds like you need to take the hood off. I have a 12g non-deluxe i got it used a while back.To take the hood off lay it flat and slide from the back of the tank to the front of the tank.You have to pull kind of hard put it will pop off. Then you can run your new cord threw the old hole.

HartfordWhalers · 02/25/2006, 06:22 PM

Thanks for all the help!

kewliz · 02/25/2006, 06:58 PM

I don't think you even need to remove the hood. Simply pull the pump from the elbow joint and the cord is free-moving. That's how I did mine. The cord is only attached to the pump.

HartfordWhalers · 02/25/2006, 09:06 PM

Rhanks for all your help im am putting in my new powerhead now!

02/25/2006, 01:28 PM	#1
HartfordWhalers Premium Member Join Date: Feb 2006 Location: Connecticut Posts: 451	Help with upgrading JBJ I just got a JBJ Nano 12g. I wanted to replace the pump so I just bought a Mini Jet 606 which people said would be good for this sized tank. I don't no how to get the power cord from the old pump out. It runs through the top of the hood. Shoould I cut it or is there some way of pulling it out without snaping anything Thanks in Advance ~Andrew This is a picture of what im talking about the cord goes through the top. Do i cut a little hole. I see the hole on the right i could run it through tehre but i still wanna get the other cord out of the chamber. Alright the picture isnt working. I cant load it oto this site. Its over 50kb. I have tried about 100 times to makwe it smaller and smaller and by the size it will work you cant see it but if you have one plase help

02/25/2006, 03:48 PM	#2
jcatblum Registered Member Join Date: May 2005 Location: Ft Sill Posts: 274	sorry wish I could help..... I am sure someone can, did you look in the DIY forum? __________________ Christina Blum Ft Sill OK Current Tank Info: 30 gal cube, 130w 50/50 PC -- also 70 W MH 10K ushio bulb- for a few SPS

02/25/2006, 06:22 PM	#4
HartfordWhalers Premium Member Join Date: Feb 2006 Location: Connecticut Posts: 451	Thanks for all the help! __________________ Oh Snap, Dipset Current Tank Info: 10g with 5.5 sump

02/25/2006, 09:06 PM	#6
HartfordWhalers Premium Member Join Date: Feb 2006 Location: Connecticut Posts: 451	Rhanks for all your help im am putting in my new powerhead now! __________________ Oh Snap, Dipset Current Tank Info: 10g with 5.5 sump

02/25/2006, 04:44 PM	#3
kelleymmm1 Registered Member Join Date: Feb 2006 Posts: 55	It sounds like you need to take the hood off. I have a 12g non-deluxe i got it used a while back.To take the hood off lay it flat and slide from the back of the tank to the front of the tank.You have to pull kind of hard put it will pop off. Then you can run your new cord threw the old hole.

02/25/2006, 06:58 PM	#5
kewliz Registered Member Join Date: Dec 2004 Posts: 715	I don't think you even need to remove the hood. Simply pull the pump from the elbow joint and the cord is free-moving. That's how I did mine. The cord is only attached to the pump.