Reef Central Online Community
Aquarium Supplies at Marine Depot

Home Forum Here you can view your subscribed threads, work with private messages and edit your profile and preferences View New Posts View Today's Posts

Find other members Frequently Asked Questions Search Reefkeeping ...an online magazine for marine aquarists Support our sponsors and mention Reef Central

Go Back   Reef Central Online Community > General Interest Forums > Do It Yourself
Register Blogs FAQ Calendar Mark Forums Read

Notices

Reply
Thread Tools
Old 01/23/2009, 12:04 PM   #1
schudini
Registered Member
 
schudini's Avatar
 
Join Date: Feb 2008
Location: In the Land of Mary
Posts: 1,988
DIY aquarium vacuum

I wanted a way to pick up waste when I was cleaning my tank. But I didn't want to buy a regular aqua vacuum cause they are battery powered and probably not strong enough. So I decided to use a Maxi-Jet powerhead (a lot of flow and corded, so more power).

At first, I used the top half of a water bottle connected to the MJ input and filled the neck with filter floss. Hand-holding the powerhead with the water bottle intake near the sand was powerful enough to pull detritus from the sand bed (avoided picking up sand by adjusting height from sandbed).

However, this was tiring and I had to be careful that the output of the MJ didn't blow frags off rocks or come shooting out of the tank, which is hard to do when you're concentrating on not sucking up all of your sandbed.

So for the next version, I decided to keep the MJ stationary using the triple suction cup mount, and move the filter intake. So I went by Lowes and found a threaded elbow that had a hose barb on the other end and a length of vinyl tubing that fit the fitting (I think its 1/2 inch).

I cut a water bottle in half and trimmed the edges so they were smooth. The bottle I used had ridges (I believe it was zeyphrhills brand).

Here are pics of the components.

click to enlarge


I cut a small hole in the bottom of the bottle that was just smaller than the diameter of the threaded elbow so that it would screw in and hold. The force of the suction kept it secure. The vinyl tubing went on the barbed side of the fitting and was secured with a ziptie (around the barbed portion) for good measure.

The mouth of the bottle fit snugly around the MJ standard filter attachment. I filled the bottle with filter floss and put the two halves together with some overlap, using the ridges to lock it.

Fully assembled.

click to enlarge


This assembly went into the tank vertically to displace the air from the tubing and floss. Then the MJ attachment went onto the powerhead. (Alternatively, you can put the attachment onto the powerhead first, then slip the mouth of the bottle onto the attachment, this prevents the attachment from accidentally being pushed inside the bottle.) Just make sure that the entire attachment is covered by the bottle so the powerhead isn't sucking in water from anywhere but through the filter. Also be sure to keep the vinyl tube in the water at all times, or it could suck air while on (and could siphon the tank when the pump is off). Point the output of the powerhead in a safe direction. The bottle might be compressed by the suction depending on how snug the two halves are connected.

And that's it. The velocity into the tube is very high, so keep it away from anything delicate (fish, soft corals, shrimp, etc) that you don't want to suck up. Also, keep it far enough from the sand bed so it just picks up detritus. It works great for vacuuming algae that you scrub off of live rock. Clears the water in no time.

When the floss is visibly dirty (or the vacuum suction decreases significantly), remove the whole assembly, drain (in the direction of filtration), remove and discard floss.

It helps to have someone helping to plug and unplug the powerhead in case you do suck up something delicate (Xenia are the worst).

You can also remove the tubing if you want to use the assembly as an additional in-tank filter.

Lastly, feel free to modify to fit your own needs. It only cost me less than $2 for all the parts (I had a spare MJ).


__________________
If man's reach exceeds his grasp, we should be careful, lest we reach our own destruction.

Current Tank Info: New tanks in the works. DIY Aquarium Vac (click my homepage)
schudini is offline   Reply With Quote
Old 01/23/2009, 04:04 PM   #2
schristi69
Master of Space and Time
 
schristi69's Avatar
 
Join Date: Aug 2005
Location: Glendale, AZ
Posts: 1,294
I have been comtemplating something like that myself. That battery powered vacum? A real POS. I bought one. I was considering using the power head to creat a suction effect. You would use like a regular siphon cleaner and mount the powerhead in the hose so it would shoot water down through the hose to the drain. This should create a vacum in the cleaner section and suck up the crud. Your idea looks to be good to clean crud out of the water after blowing off all the rocks.


__________________
"Power tends to corrupt, and absolute power corrupts absolutely" - Lord Acton

Current Tank Info: Oceanic 30gal semi cube, 20 gal live rock storage
schristi69 is offline   Reply With Quote
Old 01/23/2009, 05:31 PM   #3
dtartaglia
Registered Member
 
Join Date: Apr 2008
Location: central cali
Posts: 24
nice and detailed write up thanks man!!


dtartaglia is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 07:44 AM.


TapaTalk Enabled

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Powered by Searchlight © 2014 Axivo Inc.
Use of this web site is subject to the terms and conditions described in the user agreement.
Reef CentralTM Reef Central, LLC. Copyright 1999-2014