![]() |
![]() |
![]() |
#201 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
The drivers are no longer made and have been out of stock since February. They cannot be repaired. Your assessment may be correct but the 7240.270 driver was stronger, it was made to support the wavebox and 6200 and its development coincided with those pumps which needed a higher starting power. My guess is that the pumps are partially jammed or the drive units are worn past the optimal point and that it is not a bad driver, it is just the 7240.270 can produce more power to overcome the higher drag of worn or dirty drive units. 7240.270 came out in late 2004 so we have to assume at least the older pump was made before late 2004 and if the drive unit is still original it is past due for replacement, 6100.700 may solve the problem.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#202 |
Registered Member
Join Date: Dec 2004
Location: Brantford, Ontario, Canada
Posts: 17
|
Hi there, I have a 6100.10 attached to 7240.27 driver. Alarm has been going off even after cleaning and soaking in diluted vinegar solution. Can i send this item in for servicing and please confirm shipping address. thanks
|
![]() |
![]() |
![]() |
#203 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
We only handle the sales and service for the US, you would need to contact Phil Gilbert and Xenia, he is the distributor for Canada.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#204 |
Registered Member
Join Date: Dec 2001
Location: Calgary, AB., Canada
Posts: 1,453
|
Sorry, is that "Phil Gilbert" aka "Xenia" on RC, or are those two separate individuals? If so are they both on RC? (I ask since I'm in Canada too and since my problem sounds similar to thichmt's - only that I have one of the older drivers as well as the newer). I was going to try a replacement drive unit as you've suggested since this is an inexpensive experiment to see if it fixes things for me. Failing that then I could maybe contact the distribution point for Canada since that's where I am. Thanks!
__________________
-Tony My next hobby will be flooding my basement while repeatedly banging my head against a brick wall and tearing up $100 bills. Whee! Current Tank Info: 280g Reef, 65g FOWLR |
![]() |
![]() |
![]() |
#205 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#206 |
Registered Member
Join Date: Feb 2011
Location: North Carolina
Posts: 17
|
Hey, I spoke with you over the phone today regarding my tunze turbelle stream 6101 not working. I followed the instructions and disassembled the impeller (which was stuck in the housing as mentioned in the procedures) I cleaned it and soaked it in vinegar. I plugged ot back in and Im still getting the beeping and the pump is not pushing any water. I can hear the pump running but the impeller won't kick on. What do I need to do?
|
![]() |
![]() |
![]() |
#207 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Send it in, if we cannot repair it, we will discount an upgrade to a 6105, it sounds like you have a 6100, 6101 had no alarm. My guess is the pump is labeled 6100.100 or it may be a very last model 6100.100 with 6101 sticker.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#208 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Tunze USA
305 Victor St Austin, TX 78753 Be sure to include return address and phone number.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#209 |
Registered Member
Join Date: Jan 2007
Location: Chester VA
Posts: 59
|
Roger, I have a 6201, has rectangular transformer number 6300.240. Pump no longer works, impeller moves freely but it will not come on. When I put transformer on a 2nd 6201 that pump works fine. Can I send for repair? If so could you please provide address?
Bill |
![]() |
![]() |
![]() |
#210 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Bill,
They are a sealed unit, and there is little that can be done unless it is just an impeller issue, but I am happy to check it out and worst case scenario, we will discount a new pump. Tunze USA 305 Victor St Austin, TX 78753
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#211 | |
Registered Member
Join Date: Feb 2011
Location: North Carolina
Posts: 17
|
Quote:
Hey man, i sent the pump out today, LMK if u need anything else thanks for the great customer service thus far ![]() |
|
![]() |
![]() |
![]() |
#212 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Thanks, did you include your contact info in the box?
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#213 | ||
Registered Member
Join Date: May 2004
Location: Berkeley
Posts: 8
|
Hi Roger,
I have one older model 6200 or 6201 pump (round puck power supply, aluminum box controller) that is not working, and when I plug it in the alarm sounds. Can this pump be serviced? It doesn't appear broken, as the shaft/magnet looks OK and was not blocked. I also have a 7095 that is not working. I have two 7095s and tested the same pumps with both. I still have the same symptoms reported in the message I sent you in Aug (below). Can this be serviced? Please advise... Thanks. Jonathon Quote:
__________________
http://rtc.sfsu.edu Current Tank Info: 210G SPS tank |
||
![]() |
![]() |
![]() |
#214 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
It is unlikely the 6200 can be saved, I would have to see it, but if the drive unit is in good shape, the cause would be a dead motor and the motor is no longer made.
Regarding the 7095, there is very little that can be repaired, generally the board must be replaced. You are welcome to send them both in. Tunze USA 305 Victor St Austin, TX 78753
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#215 |
Registered Member
Join Date: May 2004
Location: Berkeley
Posts: 8
|
Roger,
The new controller and y-adapter has been running for a couple of weeks now with no issues until today. I heard the controller alarm going off (high pitched whine noise) and noticed that one of the pumps that is paired on a y-adapter channel was not running. When I unplugged that pump the whine did not stop. However, when I unplugged the other pump from that y-adapter channel, the whine did stop and the pump that was previously not running started to run again. Suggestions as to what might be going on and what needs to be fixed? Thanks!
__________________
http://rtc.sfsu.edu Current Tank Info: 210G SPS tank |
![]() |
![]() |
![]() |
#216 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Usually an alarm is a pump issue, the pump is partially jammed by calcium build up or a foreign object and needs to be cleaned.
I would check this first and if that does not solve it try running the pumps directly connected to the controller, it may be the Y adapter but this would be unusual
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#217 |
Premium Member
![]() Join Date: Jul 2002
Location: Wilmington, North Carolina
Posts: 13,860
|
Hey Roger,
Long time buddy. I have a question for you. I have an old school 6200 and the driver alarm went off. I had just cleaned it but I took it out and cleaned it again. I plugged it in and it ran fine for a few days then the alarm went off. I unplugged it, waited for a few hours, plugged back in and it worked fine. A few days later the alarm has gone off again. Is this something I can send to you for service? I understand that this pump is years out of warranty. Thanks, Sean
__________________
My tank was cool. Current Tank Info: Barebottom (the tank not me...at least not at the moment). |
![]() |
![]() |
![]() |
#218 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Yes, of course. I suspect either it needs a new drive unit or possibly just a new bearing. Good to see you around, Happy Memorial Day!
Tunze USA 305 Victor St Austin, TX 78753
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#219 |
Premium Member
![]() Join Date: Jul 2002
Location: Wilmington, North Carolina
Posts: 13,860
|
Thanks Roger,
Sending it out Monday. Just LMK what I owe. Sean
__________________
My tank was cool. Current Tank Info: Barebottom (the tank not me...at least not at the moment). |
![]() |
![]() |
![]() |
#220 |
Registered Member
Join Date: Apr 2005
Posts: 117
|
Is this address still current to send in pumps for repairs? I have a 6100 I cleaned and am still getting the driver alarm.
Tunze USA 305 Victor St Austin, TX 78753 Thanks Norm Morton |
![]() |
![]() |
![]() |
#221 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
Yes, but please be aware that very little can be done for a 6100 as the motors and drivers have not been available since 2009. In general repair will be with used parts if possible or an upgrade to a 6105 which is about $200. Be sure to include a note with return address and phone number.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#222 | |
Premium Member
![]() Join Date: Jul 2005
Location: Sault Ste Marie
Posts: 410
|
Quote:
Thanks for your help Roger. My pump 6105 is still not working despite receiving the tiny control box from Xenia. I just bought the pump used and not being familiar with the product…I happened to notice that the pump does not have the o ring on the far left of the pic as well as the black "collar" on the far right Far right of the pic. Could this be a potential cause for the pump to not function (I am assuming yes)…as well as being the cause for the power supply light to flash or dim when the pump is connected??
__________________
Like my Grandfather...I wish to die peacefully in my sleep....unlike the screaming passengers in his car Current Tank Info: 130g mixed reef. |
|
![]() |
![]() |
![]() |
#223 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
6105 is completely different design, the parts shown above would not be present. A picture of what you have would be helpful as there are two drive unit designs for the 6105 one pre Nov 2011, and one since. The basic drive unit is the same but the shaft is different, removable in the older ones and permanently fixed in the motor in later ones.
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
#224 |
Premium Member
![]() Join Date: Jul 2005
Location: Sault Ste Marie
Posts: 410
|
This is everything Roger. Thanks
__________________
Like my Grandfather...I wish to die peacefully in my sleep....unlike the screaming passengers in his car Current Tank Info: 130g mixed reef. |
![]() |
![]() |
![]() |
#225 |
RC Sponsor
![]() Join Date: Apr 2000
Location: Austin Texas USA
Posts: 35,785
|
The images don't come up for me. Can you email me Tunze at sbcglobal dot net
__________________
Roger Vitko Tunze USA "He's for every one of us, stands for every one of us, he'll save every man, woman and child in a mighty Flash!" Current Tank Info: 210 gallon planted tank with Altum Angelfish |
![]() |
![]() |
![]() |
|
|