New A360W Kessil install assistance

[Cozwey]

Well I am hoping for a little help with my new LED.

I have the Kessil installed including the cable run and plugged into my full Apex in plug V1/V2.
As soon as I plugged it in the light shut off and I have not been able to get it back on using simple statements.
I have found an initial starting point for programming that I can tinker with (Thanks Aquamanic).

So my questions are;
1 Do I use a variable speed outlet?
2 Do I somehow have to let the Apex know it has a Kessil (like the Vortech's?)
3 Do I need to program all the profiles in before it will work?

I basically just need to get a starting point.

[aquamanic]

Yes, No, Yes if you want a program.

You should be able to just turn the outlets ON via the Dashboard and the light should go full intensity and bright white. Program or no program.

[Cozwey]

OMG!

I am trying to do too much at once.
I just realized it was plugged into the wrong jack.
I received a shipment today including a second EB8 and the Kessil. I am moving things all around and running cords in bundles and a general overhaul.
I missed a small simple step.

Thanks for the help sir.

[Cozwey]

Ok I have the unit plugged in and I have install the cable. I have pirated this programming from you. My question is do I enter all of the Varspd 1 and varspd 2 information on the same outlet?

Also do I turn the spectrum and intensity up to full on the Kessil itself?
[Varspd1 spectrum]
If Time 06:00 to 07:30 Then color10k
If Time 07:30 to 09:00 Then color15k
If Time 09:00 to 13:00 Then color20k
If Time 13:00 to 16:00 Then color20k
If Time 16:00 to 18:00 Then color75
If Time 18:00 to 22:00 Then color15k

[varspd2 intensity]
If Time 06:00 to 08:00 Then sunrise
If DoW -MTWTF- Then OFF
If Time 07:00 to 09:00 Then sunrise
If Time 09:00 to 19:00 Then midday
If Time 19:00 to 20:00 Then sunset
If FeedA 000 Then midday

Here's what the profiles look like:
[ sunrise ] ( PF16 )
Type: Ramp
Ramp Time: 60
Start Intensity: 12
End Intensity: 100
[ sunset ] ( PF17 )
Type: Ramp
Ramp Time: 60
Start Intensity: 100
End Intensity: 0
[ color10k ] ( PF18 )
Type: Ramp
Ramp Time: 1
Start Intensity: 20
End Intensity: 20
[ color15k ] ( PF19 )
Type: Ramp
Ramp Time: 1
Start Intensity: 50
End Intensity: 50
[ color20k ] ( PF20 )
Type: Ramp
Ramp Time: 1
Start Intensity: 100
End Intensity: 100
[ midday ] ( PF21 )
Type: Ramp
Ramp Time: 1
Start Intensity: 100
End Intensity: 100
[ color75 ] ( PF22 )
Type: Ramp
Ramp Time: 1
Start Intensity: 75
End Intensity: 75

[Cozwey]

NVM I think I get it now. The second set of statements goes in Vr2 as this is still off the same plug on the brain unit for Apex.

[Cozwey]

Ok well it is after 22:00 and the Kessil is still on. I was hoping it would shut down based on this profile [ sunset ] ( PF17 )
Type: Ramp
Ramp Time: 60
Start Intensity: 100
End Intensity: 0

What would I have done wrong here?